How to Fix a Sliding Closet Door? Complete Guide

How to Fix a Sliding Closet Door?

How to fix a sliding closet door? Sliding closet doors are commonly used in most homes. Sliding closet doors are an easy and inexpensive way to save space in any room. Everyone who has sliding closet doors in their home will, at some point, face the frustrating problem of the doors not sliding.

Sliding closet doors are both simple and common. In most cases, sliding closet door repairs are simple. You can complete sliding closet door repairs with a few simple tools and no special experience is required.

Preparation of How to Fix a Sliding Closet Door?

Preparing to repair sliding closet doors is easy. First, make sure nothing is blocking the sliding closet doors. You are sure something has fallen behind the door. Second, make sure the door you’re trying to repair is a sliding closet door or bifold door rather than a pocket door. Pocket doors, do not slide into the wall. This is not a manual for pocket door repair.

How Much Does It Cost to Replace Closet Doors?

Depending on size and style, sliding closet doors cost between $50 to $200. For example, the Econoline 59″x80″ Painted Steel Aztec Gold Mirror Bypass Doors are $97 at Home Depot.

How To Fix a Sliding Closet Door? Step By Step

1. Replace Damaged Roller Wheels

If the door is on track but still does not slide smoothly. So you should check the wheels. Closet doors usually have wheels on top or sometimes on the bottom. So you must derail the door. So, you can see rolling hardware.

Check for damage on rolling hardware. The wheels can sometimes be chewed, warped or distorted. If the wheels are slightly bent you can try to manually bend them back into position. If the wheels are damaged they may need to be replaced. You can purchase a replacement kit at your neighborhood hardware store.

2. Check the Track

Now check the track if the wheels are in good condition. There is a possibility that dirt, debris or wear is blocking the track. Check the track length with the door open. And look for stains or damage. Sometimes the track may be bent, bent or cracked. Any of these problems can make the door difficult to open and close.

The track should be completely cleaned with the door open. Wipe the entire length of the track with a rag. Additionally you absorb the tracks using a vacuum. In this circumstance, a shop vacuum will also be effective.

3. Replace Track

If the track is damaged it should be replaced. The task of changing it is not too difficult, so don’t worry. After measuring the current track make a note of its length. Then buy a new track at your neighborhood hardware store or online.

By removing the screws, you remove the old track from the door frame. Simply insert the new track into the existing space and secure it with screws once you have it. If the measurements are accurate, the track will fit properly.

4. Check the Doors for Warps or Damage

If none of those troubleshooting steps work, there may be a problem with the door slab. Doors are prone to warping over time, especially if they are exposed to moisture or water. Lay the doors flat and check them for bends or waves. Confirm the sides and top. If you notice any waves or warps, the door itself may be the cause of the problem.

Closet door slabs can often be purchased off the shelf at home improvement stores. And it requires no special machining or preparation. Measure its standard width and height.

After purchasing the new slab, shop for a closet door hardware kit. Simply screw the new hardware into the unprepared slab and hang the door back on the track to replace it.

5. Reattach the Door

Now, with the new track fixed in place, do a good job of rearranging the door. If the track is new and the hardware is in good condition, realignment is easy and efficient.

6. Lubricate the Tracks

Tracks should be lubricated for smooth sliding. Before applying lubricant, make sure the tracks are thoroughly clean; otherwise, the lubricant will just attract dirt and cause further clogging.

The tracks can be easily lubricated with WD-40. Simply spray some WD-40 along the track’s length and wait for it to dry. Whether they are new or not, the doors should now slide much more easily.